Burks Pump GNB7-2-ME Base Mounted Pump, pedestal pump end less motor

Burks Pump GNB7-2-ME

Burks # GNB7-2-ME

Burks catalog # GNB7-2-ME, Base Mounted Pump, pedestal (frame mounted) pump end less motor, Bronze Fitted, with radial split Cast Iron casing with bronze wear ring, 7.56 inch bronze enclosed impeller (full size), steel shaft with bronze shaft sleeve, EPT mechanical seal, 2-1/2 inch NPT suction x 2 inch NPT discharge, GNB grease lubricated ball bearing power frame with 1-1/8 Inch shaft, for 1750 or 3500 RPM drive.

Price : $ 5468.40

Qty :

Can Ship : 4 Weeks (out of stock)

 

Product Information :

The Burks GNB7-2-ME is a Base Mounted Pump, a pedestal (frame mounted) centrifugal pump end less motor, Bronze Fitted, with a radial split Cast Iron casing and Bronze wear ring, a 7.56 Inch Bronze enclosed Impeller (full size), Steel shaft with Bronze shaft sleeve, EPT Mechanical Seal, 2-1/2 Inch NPT Suction x 2 Inch NPT Discharge, on the GNB grease lubricated ball bearing power frame, for 1750 or 3500 RPM drive. The Burks GNB Series are base mounted, pedestal centrifugal pump ends for frame mounting to a motor or engine, bronze fitted, with a radial split close grain cast iron casing (30,000 PSI minimum tensile) in a back pull-out design so the casing stays in the line for service, centerline discharge, a stud mounted casing that rotates to eight discharge positions, and openings for gauges, venting and draining. Enclosed bronze impeller, balanced and double locked to the shaft with key and cap screw, trimmed to the duty point; replaceable bronze casing wear ring; self adjusting mechanical shaft seal with ceramic seat and carbon face, to 225 degrees F and 150 PSI, with a tapped flushing opening. The GNB (B) power frame has grease lubricated ball bearings rated for two years minimum service at maximum load, oil seals on both bearings, a gasketed bronze shaft sleeve on a steel shaft, and tapped relubrication openings. Every pump is factory tested and meets Hydraulic Institute standards. This pump is bronze fitted, the GNB7-2 with the full size 7.56 inch, with the Carbon/Ceramic/EPT mechanical seal. Suction and discharge connections are 2-1/2 Inch NPT Suction x 2 Inch NPT Discharge.


Parts and Accessories for Burks model GNB7-2-ME


Minor Service Kit :

Catalog # SKGNB7-21271-20418, Seal kit, EPT, GNB7: Carbon/Ceramic/EPT mechanical seal 21271P, flat casing gasket 20418, and the EPT casing, impeller, adapter and bearing housing O-rings

Price: $ 501.60

Qty :

Can Ship : Same Day (2 in stock)


Impeller :

Catalog # 20420-7.56, Impeller, 7.56 inch Diameter, Bronze

Price: $ 2880.90

Qty :

Can Ship : Same Day (2 in stock)


Shaft Seal :

Catalog # 21271P, Mechanical seal, 1-1/4 inch, EPDM, for hot water or caustic service

Price: $ 345.40

Qty :

Can Ship : Same Day (7 in stock)


Gasket/O-ring :

Catalog # 20418, Casing gasket, flat, 7 series

Price: $ 68.20

Qty :

Can Ship : Same Day (2 in stock)

Applications

The Burks GNB Series base mounted centrifugal pumps are pedestal, frame mounted pump ends for coupling to a motor or engine, with a radial split close grain cast iron casing with back pull-out design, centerline discharge and a replaceable bronze wear ring, enclosed bronze impeller, and a grease lubricated ball bearing power frame with oil seals on both bearings and a gasketed bronze shaft sleeve.

This model is the GNB7-2 with the impeller at the full 7.56 inch diameter. For 1750 or 3500 RPM drive; the duty point and horsepower come from the diameter and speed on the performance curve. The impeller can be trimmed to any diameter on the curve for a specific head and capacity.

Maximum liquid temperature is 225 degrees F with the standard Buna seal, inlet pressure 100 PSI, case working pressure 200 PSI; the GNB (B) power frame carries 20 HP at 3500 RPM, 15 HP at 1750 RPM. A coupling guard is required and is not furnished with the pump only. Every pump is factory tested and meets Hydraulic Institute standards.