Burks catalog # ET7M-ABME, Base Mounted Turbine Pump, pedestal (frame mounted) pump end less motor, regenerative turbine, All Bronze, with Bronze frame and case, Bronze impeller with Monel blades, Bronze raceway, 303 Stainless Steel shaft, EPT mechanical seal, 1 inch NPT suction x 1 inch NPT discharge, ET grease lubricated ball bearing power frame, for 1750 or 3500 RPM. Built from the stocked ET7MAB with the EPT seal fitted.
Price : $ 2592.90
The Burks ET7M-ABME is a Base Mounted Turbine Pump, a pedestal (frame mounted) regenerative turbine pump end less motor, All Bronze, with a Bronze frame and case, Bronze Impeller with Monel blades, Bronze raceway, 303 Stainless Steel shaft, EPT Mechanical Seal, 1 Inch NPT Suction x 1 Inch NPT Discharge, on the ET grease lubricated ball bearing power frame, for 1750 or 3500 RPM. The Burks ET Series pumps are base mounted regenerative turbine pump ends, pedestal mounted for coupling to a motor or engine, for clean, non-abrasive, lower viscosity liquids on low flow, high pressure duty. Cast Iron frame and case with a Monel bladed bronze impeller, bronze raceway with cast-in vortex pockets (will not vapor lock) and 303 Stainless Steel shaft; all bronze construction available. Grease lubricated ball bearing power frame with wide bearing spacing, tapped and plugged openings for relubrication and grease relief holes. Life-Lok external impeller adjustment, exclusive to Burks, readjusts the impeller without disturbing the piping, disassembling the pump or replacing parts, for up to 40 percent longer service life. Carbon/ceramic mechanical shaft seal for temperatures to 225 degrees F; back pull-out, the casing stays in the line for service. Every pump is factory tested. This pump is all bronze construction, the ET7M pedestal pump end less motor, with the Carbon/Ceramic/EPT mechanical seal and EPT elastomers. Suction and discharge connections are 1 Inch NPT Suction x 1 Inch NPT Discharge.
Minor Service Kit :
Catalog # SKET-20764-22134, Seal kit, EPT, ET Series: Carbon/Ceramic/EPT mechanical seal 20764-C, EPT O-ring gasket 22134
Price: $ 1799.60
Shaft Seal :
Catalog # 20764-C, Mechanical seal, 5/8 inch, EPT, for hot water or caustic service
Price: $ 1778.70
The Burks ET Series base mounted regenerative turbine pumps are pedestal (frame mounted) pump ends for coupling to a motor or engine, for clear water and other clean, non-abrasive, lower viscosity liquids on low flow, high pressure duty - boiler feed on steam process applications (to a 38 HP boiler at a 3 to 1 safety factor), condensate return, high temperature water and oil heat transfer, hot and cold water circulation, brine and hydraulic oil circulation, jockey pump, pressure booster, high pressure spray and additive metering. Burks is the only regenerative turbine with the Life-Lok external impeller adjustment, in the power frame, which restores the impeller to raceway clearance, and the pump's pressure, without disturbing the piping or taking the pump apart.
The ET7M is the size 7 pump end for 1750 or 3500 RPM, rated 8.3 GPM at 20 feet of total head at 3450 RPM and 3.4 GPM at 1750 RPM, with heads to 350 feet (150 PSI). Motor size follows the duty point on the performance curve. All bronze construction - bronze frame and case, bronze impeller with Monel blades, bronze raceway.
Maximum liquid temperature 225 degrees F with the standard Buna-N seal, inlet pressure 100 PSI, casing working pressure 250 PSI. A coupling guard is required and is not furnished with the pump only; the price book lists bases, couplings and guards by motor frame. A strainer of about 20 mesh should be fitted on the suction side to keep chips and scale out of the raceway and impeller. Every pump is factory tested.
This model carries the EPT mechanical seal, EPT O-ring gasket in place of the standard Buna-N ones.