Burks catalog # ES8M-ABMV, Base Mounted Turbine Pump, pedestal (frame mounted) pump end less motor, regenerative turbine, All Bronze, with Bronze frame and case, Bronze impeller with Monel blades, Bronze raceway, 303 Stainless Steel shaft, Viton mechanical seal, 1-1/4 inch NPT suction x 1 inch NPT discharge, ES grease lubricated ball bearing power frame, for 1750 or 3500 RPM. Built from the stocked ES8MAB with the Viton seal fitted.
Price : $ 4178.70
The Burks ES8M-ABMV is a Base Mounted Turbine Pump, a pedestal (frame mounted) regenerative turbine pump end less motor, All Bronze, with a Bronze frame and case, Bronze Impeller with Monel blades, Bronze raceway, 303 Stainless Steel shaft, Viton Mechanical Seal, 1-1/4 Inch NPT Suction x 1 Inch NPT Discharge, on the ES grease lubricated ball bearing power frame, for 1750 or 3500 RPM. The Burks ES Series pumps are base mounted regenerative turbine pump ends, pedestal mounted for coupling to a motor or engine, for clean, non-abrasive, lower viscosity liquids on low flow, high pressure duty. Cast Iron frame and case with a Monel bladed bronze impeller, bronze raceway with cast-in vortex pockets (will not vapor lock) and 303 Stainless Steel shaft; all bronze construction available. Grease lubricated ball bearing power frame with wide bearing spacing, tapped and plugged openings for relubrication and grease relief holes. Life-Lok external impeller adjustment, exclusive to Burks, readjusts the impeller without disturbing the piping, disassembling the pump or replacing parts, for up to 40 percent longer service life. Carbon/ceramic mechanical shaft seal for temperatures to 225 degrees F; back pull-out, the casing stays in the line for service. Every pump is factory tested. This pump is all bronze construction, the ES8M pedestal pump end less motor, with the Carbon/Ceramic/Viton mechanical seal and Viton elastomers. Suction and discharge connections are 1-1/4 Inch NPT Suction x 1 Inch NPT Discharge.
Major Overhaul Kit / Rebuild Kit :
Catalog # 20522-8-MV, Repair kit, Crane, Viton, for the CS8M: impeller, raceway, mechanical seal, O-ring gasket, impeller lock nut, suction sleeve, raceway screws, shaft key and instructions, Major Repair Kit
Price: $ 2394.70
Minor Service Kit :
Catalog # SKES-9813-9817, Seal kit, Viton, ES Series: Carbon/Ceramic/Viton mechanical seal 09813-C, Viton O-ring gasket 09817, Viton suction sleeve 09695
Price: $ 629.20
Shaft Seal :
Catalog # 09813-C, Mechanical seal, 3/4 inch, Carbon/Ceramic/Viton
Price: $ 345.40
Casing frozen or cracked ? New Pump Casing :
Catalog # 09790-C, Case, Bronze, all bronze construction
Price: $ 1432.20
The Burks ES Series base mounted regenerative turbine pumps are pedestal (frame mounted) pump ends for coupling to a motor or engine, for clear water and other clean, non-abrasive, lower viscosity liquids on low flow, high pressure duty - boiler feed on steam process applications, condensate return, high temperature water and oil heat transfer, hot and cold water circulation, brine and hydraulic oil circulation, jockey pump, pressure booster, high pressure spray and additive metering. Burks is the only regenerative turbine with the Life-Lok external impeller adjustment, in the power frame, which restores the impeller to raceway clearance, and the pump's pressure, without disturbing the piping or taking the pump apart.
The ES8M is the size 8 pump end for 1750 or 3500 RPM, rated 26.2 GPM at 20 feet of total head at 3450 RPM and 12.1 GPM at 1750 RPM, with heads to 350 feet (150 PSI). Motor size follows the duty point on the performance curve. All bronze construction - bronze frame and case, bronze impeller with Monel blades, bronze raceway.
Maximum liquid temperature 225 degrees F with the standard Buna-N seal, inlet pressure 100 PSI, casing working pressure 250 PSI. A coupling guard is required and is not furnished with the pump only; the price book lists bases, couplings and guards by motor frame. A strainer of about 20 mesh should be fitted on the suction side to keep chips and scale out of the raceway and impeller. Every pump is factory tested.
This model carries the Viton mechanical seal, Viton O-ring gasket, Viton suction sleeve in place of the standard Buna-N ones.