Burks Pump EC8MV Base Mounted Turbine Pump, pedestal pump end less motor

Burks Pump EC8MV

Burks # EC8MV

Burks catalog # EC8MV, Base Mounted Turbine Pump, pedestal (frame mounted) pump end less motor, regenerative turbine, Bronze Fitted, with Cast Iron frame and case, built-on suction strainer, Bronze impeller with Monel blades, Bronze raceway, 303 Stainless Steel shaft, Viton mechanical seal, 1-1/2 inch NPT suction x 1-1/4 inch NPT discharge, C grease lubricated ball bearing power frame, for 1750 RPM. Built from the stocked EC8M with the Viton seal fitted.

Price : $ 5567.40

Qty :

Can Ship : Next Day (1 unit available)

Click Here for PARTS

 

Product Information :

The Burks EC8MV is a Base Mounted Turbine Pump, a pedestal (frame mounted) regenerative turbine pump end less motor, Bronze Fitted, with a Cast Iron frame and case with built-on suction strainer, Bronze Impeller with Monel blades, Bronze raceway, 303 Stainless Steel shaft, Viton Mechanical Seal, 1-1/2 Inch NPT Suction x 1-1/4 Inch NPT Discharge, on the C grease lubricated ball bearing power frame, for 1750 RPM. The Burks EC Series pumps are base mounted regenerative turbine pump ends, pedestal mounted for coupling to a motor or engine, for clean, non-abrasive, lower viscosity liquids on low flow, high pressure duty. Cast Iron frame and case with a Monel bladed bronze impeller, bronze raceway with cast-in vortex pockets (will not vapor lock) and 303 Stainless Steel shaft; all bronze construction available. Grease lubricated ball bearing power frame with wide bearing spacing, tapped and plugged openings for relubrication and grease relief holes. Life-Lok external impeller adjustment, exclusive to Burks, readjusts the impeller without disturbing the piping, disassembling the pump or replacing parts, for up to 40 percent longer service life. Carbon/ceramic mechanical shaft seal for temperatures to 225 degrees F; back pull-out, the casing stays in the line for service. Every pump is factory tested. This pump is bronze fitted construction, the EC8M pedestal pump end less motor, with the Carbon/Ceramic/Viton mechanical seal and Viton elastomers. Suction and discharge connections are 1-1/2 Inch NPT Suction x 1-1/4 Inch NPT Discharge.


Parts and Accessories for Burks model EC8MV


Major Overhaul Kit / Rebuild Kit :

Catalog # 21707-08, Repair kit, Crane, for the EC8M: impeller, raceway and instructions, Major Repair Kit

Price: $ 7408.50

Qty :

Can Ship : Same Day (2 in stock)


Minor Service Kit :

Catalog # SKEC-9813-9695, Seal kit, Viton, EC Series: Carbon/Ceramic/Viton mechanical seal 09813-C, Viton suction sleeve 09695, Viton seal housing gasket 21547, Viton case gasket 21548, Viton strainer gasket 21733

Price: $ 654.50

Qty :

Can Ship : Same Day (2 in stock)


Shaft Seal :

Catalog # 09813-C, Mechanical seal, 3/4 inch, Carbon/Ceramic/Viton

Price: $ 345.40

Qty :

Can Ship : Same Day (5 in stock)


Casing frozen or cracked ? New Pump Casing :

Catalog # 21304, Case, Cast Iron, EC

Price: $ 1036.20

Qty :

Can Ship : Same Day (2 in stock)

Applications

The Burks EC Series base mounted regenerative turbine pumps are pedestal (frame mounted) pump ends for coupling to a motor or engine, for clear water and other clean, non-abrasive, lower viscosity liquids on low flow, high pressure duty - boiler feed on steam process applications, condensate return, high temperature water and oil heat transfer, hot and cold water circulation, brine and hydraulic oil circulation, jockey pump, pressure booster, high pressure spray and additive metering. Burks is the only regenerative turbine with the Life-Lok external impeller adjustment, in the power frame, which restores the impeller to raceway clearance, and the pump's pressure, without disturbing the piping or taking the pump apart.

The EC8M is the size 8 pump end for 1750 RPM, with heads to the 1750 RPM performance curve. The C power frame carries 5 HP. Bronze fitted - Cast Iron frame and case, bronze impeller with Monel blades, bronze raceway. A suction strainer with brass screen is built on.

Maximum liquid temperature 225 degrees F with the standard Buna-N seal, inlet pressure 50 PSI, casing working pressure 200 PSI. A coupling guard is required and is not furnished with the pump only; the price book lists bases, couplings and guards by motor frame. A strainer of about 20 mesh should be fitted on the suction side to keep chips and scale out of the raceway and impeller. Every pump is factory tested.

This model carries the Viton mechanical seal, Viton suction sleeve, Viton seal housing gasket, Viton case gasket, Viton strainer gasket in place of the standard Buna-N ones.