Burks catalog # EC10MABME, Base Mounted Turbine Pump, pedestal (frame mounted) pump end less motor, regenerative turbine, All Bronze, with Bronze frame and case, built-on suction strainer, Bronze impeller with Monel blades, Bronze raceway, 303 Stainless Steel shaft, EPT mechanical seal, 1-1/2 inch NPT suction x 1-1/4 inch NPT discharge, C grease lubricated ball bearing power frame, for 1750 RPM. Built from the stocked EC10MAB with the EPT seal fitted.
Price : $ 8594.10
The Burks EC10MABME is a Base Mounted Turbine Pump, a pedestal (frame mounted) regenerative turbine pump end less motor, All Bronze, with a Bronze frame and case with built-on suction strainer, Bronze Impeller with Monel blades, Bronze raceway, 303 Stainless Steel shaft, EPT Mechanical Seal, 1-1/2 Inch NPT Suction x 1-1/4 Inch NPT Discharge, on the C grease lubricated ball bearing power frame, for 1750 RPM. The Burks EC Series pumps are base mounted regenerative turbine pump ends, pedestal mounted for coupling to a motor or engine, for clean, non-abrasive, lower viscosity liquids on low flow, high pressure duty. Cast Iron frame and case with a Monel bladed bronze impeller, bronze raceway with cast-in vortex pockets (will not vapor lock) and 303 Stainless Steel shaft; all bronze construction available. Grease lubricated ball bearing power frame with wide bearing spacing, tapped and plugged openings for relubrication and grease relief holes. Life-Lok external impeller adjustment, exclusive to Burks, readjusts the impeller without disturbing the piping, disassembling the pump or replacing parts, for up to 40 percent longer service life. Carbon/ceramic mechanical shaft seal for temperatures to 225 degrees F; back pull-out, the casing stays in the line for service. Every pump is factory tested. This pump is all bronze construction, the EC10M pedestal pump end less motor, with the Carbon/Ceramic/EPT mechanical seal and EPT elastomers. Suction and discharge connections are 1-1/2 Inch NPT Suction x 1-1/4 Inch NPT Discharge.
Major Overhaul Kit / Rebuild Kit :
Catalog # 21707-10, Repair kit, Crane, for the EC10M: impeller, raceway and instructions, Major Repair Kit
Price: $ 4617.80
Minor Service Kit :
Catalog # SKEC-21934-20285, Seal kit, EPT, EC Series: Carbon/Ceramic/EPT mechanical seal 21934, EPT suction sleeve 20285, EPT seal housing gasket 22131, EPT case gasket 22136, EPT strainer gasket 22130
Price: $ 1039.50
Shaft Seal :
Catalog # 21934, Mechanical seal, 3/4 inch, Carbon/Ceramic/EPT
Price: $ 498.30
Casing frozen or cracked ? New Pump Casing :
Catalog # 21304-A, Case, Bronze, EC, all bronze construction
Price: $ 6916.80
The Burks EC Series base mounted regenerative turbine pumps are pedestal (frame mounted) pump ends for coupling to a motor or engine, for clear water and other clean, non-abrasive, lower viscosity liquids on low flow, high pressure duty - boiler feed on steam process applications, condensate return, high temperature water and oil heat transfer, hot and cold water circulation, brine and hydraulic oil circulation, jockey pump, pressure booster, high pressure spray and additive metering. Burks is the only regenerative turbine with the Life-Lok external impeller adjustment, in the power frame, which restores the impeller to raceway clearance, and the pump's pressure, without disturbing the piping or taking the pump apart.
The EC10M is the size 10 pump end for 1750 RPM, with heads to the 1750 RPM performance curve. The C power frame carries 5 HP. All bronze construction - bronze frame and case, bronze impeller with Monel blades, bronze raceway. A suction strainer with brass screen is built on.
Maximum liquid temperature 225 degrees F with the standard Buna-N seal, inlet pressure 50 PSI, casing working pressure 200 PSI. A coupling guard is required and is not furnished with the pump only; the price book lists bases, couplings and guards by motor frame. A strainer of about 20 mesh should be fitted on the suction side to keep chips and scale out of the raceway and impeller. Every pump is factory tested.
This model carries the EPT mechanical seal, EPT suction sleeve, EPT seal housing gasket, EPT case gasket, EPT strainer gasket in place of the standard Buna-N ones.