Burks Pump model # 4GNB9-3F-ME-8.50 Centrifugal Pump

Burks Pump 4GNB9-3F-ME-8.50

Burks # 4GNB9-3F-ME-8.50

Burks catalog # 4GNB9-3F-ME-8.50, Base Mounted Pump, pedestal (frame mounted) pump end less motor, Bronze Fitted, with radial split Cast Iron casing with bronze wear ring, 8.50 inch bronze enclosed impeller (trimmed from 9.25 inch), steel shaft with bronze shaft sleeve, EPT mechanical seal, 4 inch suction x 3 inch discharge, ANSI 125 pound flat face flanges, GNB grease lubricated ball bearing power frame with 1-1/8 Inch shaft, specified for 1750 RPM.

Price : $ 7907.40

Qty :

Can Ship : 4 Weeks (out of stock)

Click Here for PARTS

 

Product Information :

The Burks 4GNB9-3F-ME-8.50 is a Base Mounted Pump, a pedestal (frame mounted) centrifugal pump end less motor, Bronze Fitted, with a radial split Cast Iron casing and Bronze wear ring, a 8.50 Inch Bronze enclosed Impeller (trimmed from 9.25 Inch), Steel shaft with Bronze shaft sleeve, EPT Mechanical Seal, 4 Inch Suction x 3 Inch Discharge, ANSI 125 pound flat face flanges, on the GNB grease lubricated ball bearing power frame, specified for 1750 RPM. The Burks GNB Series are base mounted, pedestal centrifugal pump ends for frame mounting to a motor or engine, bronze fitted, with a radial split close grain cast iron casing (30,000 PSI minimum tensile) in a back pull-out design so the casing stays in the line for service, centerline discharge, a stud mounted casing that rotates to eight discharge positions, and openings for gauges, venting and draining. Enclosed bronze impeller, balanced and double locked to the shaft with key and cap screw, trimmed to the duty point; replaceable bronze casing wear ring; self adjusting mechanical shaft seal with ceramic seat and carbon face, to 225 degrees F and 150 PSI, with a tapped flushing opening. The GNB (B) power frame has grease lubricated ball bearings rated for two years minimum service at maximum load, oil seals on both bearings, a gasketed bronze shaft sleeve on a steel shaft, and tapped relubrication openings. Every pump is factory tested and meets Hydraulic Institute standards. This pump is bronze fitted, the 4GNB9-3F with the impeller trimmed to 8.50 inch, specified for 1750 RPM, with the Carbon/Ceramic/EPT mechanical seal. Suction and discharge connections are 4 Inch Suction x 3 Inch Discharge, ANSI 125 pound flat face flanges.


Applications

The Burks GNB Series base mounted centrifugal pumps are pedestal, frame mounted pump ends for coupling to a motor or engine, with a radial split close grain cast iron casing with back pull-out design, centerline discharge and a replaceable bronze wear ring, enclosed bronze impeller, and a grease lubricated ball bearing power frame with oil seals on both bearings and a gasketed bronze shaft sleeve.

This model is the 4GNB9-3F with the impeller trimmed to 8.50 inches. The 4 prefix is the catalog number for 1750 RPM duty; the pump is the same, specified for 1750 RPM. The impeller can be trimmed to any diameter on the curve for a specific head and capacity.

Maximum liquid temperature is 225 degrees F with the standard Buna seal, inlet pressure 100 PSI, case working pressure 200 PSI; the GNB (B) power frame carries 20 HP at 3500 RPM, 15 HP at 1750 RPM. A coupling guard is required and is not furnished with the pump only. Every pump is factory tested and meets Hydraulic Institute standards.