Gorman Rupp # 16001-005 Compact Bellows Pump

Gorman Rupp Pump

 

Product Information :

The Gorman Rupp Industries (GRI) model # 16001-005 is a Compact Bellows Pump and Motor unit coupled to a 90 RPM, 230 Volt AC, open, shaded pole electric Motor. These Compact Bellows Metering Pumps operate on a positive displacement principle. The rotation of the motor shaft is transmitted into an up and down linear motion through an adjustable concentric crank mechanism. This motion provides a continuous compressing and relaxing force on the bellows module, forcing fluid between two check valves located in the module's valve body. Up to four separate bellows modules can be operated by single motor for proportioning up to four separate fluid mediums. The flow rate of each module is independently adjustable. Multiple bellows modules operate out of phase with each other for most efficient power usage. Any combination of 1/2 inch, 3/4 inch, 1 inch, 1-1/2 inch and 2 inch bellows may be used in a pump. However, the total output must be limited to a maximum flow rate of 3000 ml/min.
WEIGHT : The Gorman Rupp 16001-005 weighs 3.61 Lbs.

Features :

Motor Specs :
90 RPM, 230 Volts AC. open, shaded pole.

Applications

These Compact Bellows Metering Pumps were specifically designed for metering applications requiring low discharge pressures. Compact pumps have been successfully applied in photo, Xray and dental film processors; silver recovery; and scientific and analytical instruments. The compact bellows pumps utilize GRI's proven bellows and valving technology to provide an accurate and economical metering pump with long life. The proprietary blended polypropylene materials of construction and a wide selection of valve and Oring elastomers produce chemical resistant pumps capable of handling a wide range of fluids. Typical applications for the GRI 16001005 include film and xray processors, silver recovery systems, wafer and silicon chip washers and processors, detergent dispensers, blood analyzing equipment, industrial floor scrubbers, thermo therapy equipment, waste removal systems, and wastewater and water treatment systems. Maximum fluid viscosity is 5,000 centistokes. The poppet valves in this pump can handle fine slurries. Standard motor speeds are 45.6 and 90 RPM at 60 Hz and 38 and 75 RPM at 50 Hz. Motors are UL recognized and rated with a minimum life expectancy of 2000 hours. Perpetual running of motor is not recommended. If a nonstop application is encountered, the GormanRupp Industries HeavyDuty Bellows Metering Pump is recommended.

Compact Bellows pumps have these available poppet valve and oring material options F001 / F001 EPDM, F003 / F003 Viton/FKM, F004 / F004 EPDM, F006 / F006 Viton/FKM, F007 / F007 EPDM, F009 / F009 Viton/FKM, F031 / F031 EPDM, F033 / F033 Viton/FKM, and F035 / F035 EPDM, F037 / F037 Viton/FKM. Available T code port options T001 T1, T002 T2, T003 T3, T004 T4, T005 T5, T006 T6, T007 T7, T008 T8, T009 T9, T011 T11, T012 T12, T013 T13, T014 T14, T001 T01, T002 T02, T003 T03, T004 T04, T005 T05, T006 T06, T007 T07, T008 T08, T009 T09 ports. The standard pump will be have exposed motor and bare wire leads, but cover options are also available. Available H code cover options are H001 H001, H003 H003, H004 H004, H005 H005, H006 H006, and H008 H008. In addition to the standard options listed, cover options can also include different wire or cord lengths and terminations, strain reliefs and ground wires.


 

Copyright 2023 Equipment Agents Inc.